DescriptionSTD-RCF 4 Rolling Contact Fatigue & Bearing Friction Rig may be used for both endurance
WhatsApp +86 13816217984
Email:info@qinsun-lab.com
STD-RCF 4 Rolling Contact Fatigue & Bearing Friction Rig may be used for both endurance testing and precision bearing frictional loss measurement. Two test assemblies are available:
• combined radial and axial loading
• bi-directional axial loading
Load is applied by means of servo controlled pneumatic bellows with force transducer feedback.
An in-line torque transducer is provided for friction measurement, with a maximum permissible speed of 10.000 rpm.
Bearing outer race temperatures are measured with thermocouples and a vibration sensor with adjustable level trigger circuit is provided for stopping the machine at the on-set of rolling contact fatigue.
An integral lubricant service module is fitted as standard incorporating a sump tank with immersion heater, delivery pump, scavenge pump, oil to water heat exchangers for cooling and change-over filters.
| Technical Specifications | |
| Motor: | 4 kW a.c. vector motor and drive with encoder feedback |
| Maximum Motor Speed: | 3.000 rpm |
| High Speed Drive: | Flat belt |
| Ratio: | 6.7:1 |
| Low Speed Drive: | Timing belt |
| Ratio: | 1:2 & 2:1 |
| Maximum Spindle Speed: | 10.000 rpm |
| Torque Transducer Range: | 50 Nm |
| Maximum Lubricant Supply Rate: | 6.8 l/min |
| Maximum Lubricant Supply Temperature: | Ambient to 150°C |
| Change-over Filters: | 3 micron |
| Interface: | Phoenix Tribology USB micro-controller interface |
| Software: | COMPEND 2020 |
| Controlled Parameters | Motor speed |
| Applied loads | |
| Test fluid temperature | |
| Test duration | |
| Recorded Parameters | Motor speed |
| Applied load | |
| Total bearing friction | |
| Lubricant inlet temperature | |
| Bearing outer race temperatures | |
| Vibration sensor output | |
| RCF 4/1 Combined Radial and Axial Loading | |
| Configuration: | Four bearing back-to-back |
| Bearing Types: | Taper, spherical, cylindrical roller, angular contact, deep groove ball |
| Shaft Diameters: | 40 mm to 65 mm |
| Maximum Bearing Outside Diameter: | 140 mm |
| Maximum Axial Load per Bearing: | 16 kN |
| Maximum Radial Load per Bearing: | 40 kN |
| Maximum Axial Load: | 16 kN |
| Maximum Radial Load: | 80 kN |
| RCF 4/2 Test Assembly – Bi-directional Axial Loading | |
| Configuration: | Two deep grove ball bearings back-to-back |
| Bearing Types: | Deep grove and angular contact (uni-directional loading) |
| Shaft Diameters: | 20 mm to 40 mm |
| Maximum Bearing Outside Diameter: | 90 mm |
| Maximum Axial Load Per Bearing: | 4 kN |
| Maximum Axial Load: | 4 kN |
| Services | |
| Electricity: | 415 V, three phase, 50/60 Hz, 7.5 kW |
| Clean, dry air: | 4 cfm at 8 bar (120 psi) |
| Mains water and drain: | 10 l/min (typical) |
Từ chối trách nhiệm: Nội dung trên chỉ dành cho tham khảo và giao tiếp giữa những người trong ngành và không đảm bảo tính chính xác hoặc đầy đủ của nó. Theo luật pháp và quy định có liên quan và các quy định của trang web này, các đơn vị hoặc cá nhân mua các mặt hàng liên quan phải có trình độ và điều kiện trình độ hợp lệ.
Điện thoại công ty
+86-21-6420 0566
Thời gian làm việc
Thứ Hai đến Thứ Sáu
Điện thoại di động:
13816217984
Email:
info@qinsun-lab.com
