DescriptionThe DN 33 Draw Strip/Draw Bead Tester comprises a long stroke electro mechanical bal
WhatsApp +86 13816217984
Email:info@qinsun-lab.com
The STD-DN 33 Draw Strip/Draw Bead Tester comprises a long stroke electro mechanical ball screw actuator mounted horizontally on a steel bed plate in line with a tooling fixture. The actuator has an integral LVDT for displacement measurement and is controlled by means of a standard a.c. vector drive with encoder feedback.
The tooling fixture comprises two articulated arms, each carrying one half of a draw tool. The arms are connected to a fixed point on the machine bed-plate by means of a force transducer, in such a way as to measure the combined drawing force on the arms. The clamping force on the draw tool is by means of a hydraulic cylinder with force transducer feedback and controlled by means of a proportional control valve.
The standard specimen is a long strip of material of up to 25 mm width, which is connected to the actuator by means of standard mechanical grips.
| Drawing Speed: | 200 to 2.000mm/min |
| Speed Resolution: | +/- 1% of maximum speed |
| Maximum Clamping Force: | 1 kN to 68 kN |
| Clamping Force Load Cell: | 100 kN |
| Maximum Pulling Force: | 54.8 kN (18.4 kN for a lifetime of 2500 km) |
| Drawing Force Load Cell: | 100 kN |
| Maximum Drawing Length: | 400 mm |
| Maximum Strip Size: | 525 mm x 70 mm |
| Tool Size: | 35 mm x 45 mm (typical) |
| Tool Finish: | 0.05 – 0.02 microns Ra |
| Contact Conditions: | Flat on Flat |
| Cylinder on Flat (sliding) | |
| Cylinder on Flat (rolling) | |
| Draw Bead | |
| Fixed Bead/Roller Bead | |
| VDA Standard Flat on Flat: | Length 145 mm x Width 70 mm |
| Additional Features: | Strip Heating – Ceramic |
| Tool Heating – Cartridge | |
| Thermocouples x 2 | |
| Pyrometers x 2 | |
| Actuator: | Electro-thrust Ballscrew with a.c. Servo Motor |
| Clamping Force: | Hydraulic Ram |
| Power Pack: | 2 l/min at 210 bar |
| Interface: | USB Serial Link Interface Module |
| Software: | COMPEND 2000 |
| Automatically Controlled Parameters | Drawing Speed |
| Specimen Load | |
| Measured Parameters | Drawing Speed |
| Specimen Load | |
| Drawing Friction Force | |
| Drawing Displacement | |
| Services | |
| Electricity: | 220/240V, single phase, 50 Hz, 7.5 kW |
| 110/120 V, single phase, 60 Hz, 7.5 kW | |
| Installation | |
| Floor-standing: | 900 mm wide x 600 mm deep x 1.200 mm high, 250 kg |
| Control cabinet: | 530 mm x 800 mm x 300 mm high, 20 kg |
Từ chối trách nhiệm: Nội dung trên chỉ dành cho tham khảo và giao tiếp giữa những người trong ngành và không đảm bảo tính chính xác hoặc đầy đủ của nó. Theo luật pháp và quy định có liên quan và các quy định của trang web này, các đơn vị hoặc cá nhân mua các mặt hàng liên quan phải có trình độ và điều kiện trình độ hợp lệ.
Điện thoại công ty
+86-21-6420 0566
Thời gian làm việc
Thứ Hai đến Thứ Sáu
Điện thoại di động:
13816217984
Email:
info@qinsun-lab.com
